Titanium and titanium alloy bar per MIL-T-9047 is a specialty at Flight Metals. MIL-T-9047 is the military specification for aircraft quality titanium bar (rolled or forged) and reforging stock, and it covers 16 compositions: commercially pure titanium (CP-70), alpha alloys such as Ti-5Al-2.5Sn, alpha-beta alloys such as Ti-6Al-4V (Grade 5, UNS R56400), Ti-6Al-4V ELI, Ti-6Al-6V-2Sn and Ti-6Al-2Sn-4Zr-6Mo, and beta alloys such as Ti-3Al-8V-6Cr-4Mo-4Zr (Beta C). Bars are supplied annealed, duplex annealed, solution treated or solution treated and aged, depending on the alloy and the condition ordered. Minimum tensile properties by alloy, condition and size are listed below, and we can provide MIL-T-9047 in round, square and rectangular bar. Applications include fasteners, fittings, landing gear and airframe components, engine parts and defense hardware. Inquire today to receive pricing on your MIL-T-9047 titanium bar requirement.
About MIL-T-9047:
MIL-T-9047 (latest revision G) covers aircraft quality commercially pure, alpha, alpha-beta and beta titanium alloy bars, hot worked with or without cold finishing, and reforging stock. Bars are supplied in Condition A (annealed), DA (duplex annealed), ST (solution treated) or STA (solution treated and aged), as ordered, with Surface Finish I (ground, machined or descaled and pickled free of alpha case) unless Surface Finish II is specified. Unlike MIL-T-9046, which uses codes such as AB-1, the bar specification identifies each alloy by its composition. Minimum tensile properties depend on alloy, condition and size. For example, annealed Ti-6Al-4V bar 4.00″ and under has a minimum tensile strength of 130 ksi, while STA Ti-6Al-4V rounds 0.500″ and under have a minimum of 165 ksi. The aerospace equivalents for Ti-6Al-4V bar are AMS 4928 (annealed) and AMS 4965 (STA).
| Alloy | Class |
|---|---|
| CP-70 | Commercially pure |
| Ti-5Al-2.5Sn | Alpha |
| Ti-8Al-1Mo-1V | Alpha |
| Ti-3Al-2.5V | Alpha-beta |
| Ti-6Al-4V | Alpha-beta |
| Ti-6Al-4V ELI | Alpha-beta |
| Ti-6Al-6V-2Sn | Alpha-beta |
| Ti-6Al-2Sn-4Zr-2Mo | Alpha-beta |
| Ti-6Al-2Sn-4Zr-6Mo | Alpha-beta |
| Ti-3Al-8V-6Cr-4Mo-4Zr | Beta |
Chemical Composition by Alloy (wt %):
| Alloy | Alloying Additions | Iron | Carbon | Nitrogen | Hydrogen | Oxygen | Other Total |
|---|---|---|---|---|---|---|---|
| CP-70 | — | 0.50 | 0.08 | 0.05 | 0.0125 | 0.40 | 0.30 |
| Ti-5Al-2.5Sn | Al 4.50–5.75, Sn 2.00–3.00 | 0.50 | 0.08 | 0.05 | 0.020 | 0.20 | 0.40 |
| Ti-5Al-2.5Sn ELI | Al 4.50–5.75, Sn 2.00–3.00 | 0.25 | 0.05 | 0.035 | 0.0125 | 0.12 | 0.30 |
| Ti-6Al-2Cb-1Ta-0.8Mo | Al 5.50–6.50, Cb 1.50–2.50, Ta 0.50–1.50, Mo 0.50–1.00 | 0.25 | 0.05 | 0.03 | 0.0125 | 0.10 | 0.40 |
| Ti-8Al-1Mo-1V | Al 7.35–8.35, Mo 0.75–1.25, V 0.75–1.25 | 0.30 | 0.08 | 0.05 | 0.015 | 0.15 | 0.40 |
| Ti-3Al-2.5V | Al 2.50–3.50, V 2.00–3.00 | 0.30 | 0.05 | 0.02 | 0.015 | 0.12 | 0.40 |
| Ti-6Al-4V | Al 5.50–6.75, V 3.50–4.50 | 0.30 | 0.08 | 0.05 | 0.015 | 0.20 | 0.40 |
| Ti-6Al-4V ELI | Al 5.50–6.50, V 3.50–4.50 | 0.25 | 0.08 | 0.05 | 0.0125 | 0.13 | 0.30 |
| Ti-6Al-6V-2Sn | Al 5.00–6.00, V 5.00–6.00, Sn 1.50–2.50, Cu 0.35–1.00 | 0.35–1.00 | 0.05 | 0.04 | 0.015 | 0.20 | 0.30 |
| Ti-6Al-2Sn-4Zr-2Mo | Al 5.50–6.50, Sn 1.80–2.20, Zr 3.60–4.40, Mo 1.80–2.20, Si 0.13 max | 0.25 | 0.05 | 0.04 | 0.015 | 0.15 | 0.30 |
| Ti-6Al-2Sn-4Zr-6Mo | Al 5.50–6.50, Sn 1.75–2.25, Zr 3.60–4.40, Mo 5.50–6.50 | 0.15 | 0.04 | 0.04 | 0.0125 | 0.15 | 0.40 |
| Ti-7Al-4Mo | Al 6.50–7.30, Mo 3.50–4.50 | 0.30 | 0.10 | 0.05 | 0.013 | 0.20 | 0.40 |
| Ti-8Mo-8V-2Fe-3Al | Mo 7.50–8.50, V 7.50–8.50, Al 2.60–3.40 | 1.60–2.40 | 0.05 | 0.05 | 0.015 | 0.16 | 0.40 |
| Ti-11.5Mo-6Zr-4.5Sn | Mo 10.00–13.00, Zr 4.50–7.50, Sn 3.75–5.25 | 0.35 | 0.10 | 0.05 | 0.020 | 0.18 | 0.40 |
| Ti-3Al-8V-6Cr-4Mo-4Zr | Al 3.00–4.00, V 7.50–8.50, Cr 5.50–6.50, Mo 3.50–4.50, Zr 3.50–4.50 | 0.30 | 0.05 | 0.03 | 0.020 | 0.12 | 0.40 |
| Ti-13V-11Cr-3Al | V 12.50–14.50, Cr 10.00–12.00, Al 2.50–3.50 | 0.35 | 0.05 | 0.05 | 0.025 | 0.17 | 0.40 |
Single values are maximums. Titanium is the balance. Yttrium 0.005% max for all alloys. Other elements 0.10% max each unless noted; Ti-5Al-2.5Sn ELI is limited to 0.05% each, and its iron plus oxygen may not exceed 0.32%. Hydrogen is determined on each lot as shipped.
Tensile Requirements – CP & Alpha Alloys (Annealed):
| Alloy | Thickness, Diameter or Distance Between Flats | Tensile Strength (KSI) | Yield Strength at 0.2% (KSI) | % Elongation in 4D | % Reduction of Area |
|---|---|---|---|---|---|
| CP-70 | 4.00″ & under | 80 | 70 | 15 | 30 |
| Ti-5Al-2.5Sn | 4.00″ & under | 115 | 110 | 10 [8] | 25 [20] |
| Ti-5Al-2.5Sn ELI | 3.00″ & under | 100 | 90 | 10 [8] | 25 [20] |
| Ti-5Al-2.5Sn ELI | 3.00″ – 4.00″ | 100 | 90 | 10 [8] | 20 [15] |
| Ti-6Al-2Cb-1Ta-0.8Mo | 4.00″ & under | 103 | 95 | 10 [8] | 20 [15] |
| Ti-8Al-1Mo-1V (DA) | 2.50″ & under | 130 | 120 | 10 | 20 |
| Ti-8Al-1Mo-1V (DA) | 2.50″ – 4.00″ | 120 | 110 | 10 [8] | 20 [15] |
Minimum values for products with a cross-sectional area of 16 sq. in. or less, in any grain direction. Ti-8Al-1Mo-1V is supplied duplex annealed (DA) only. Values in brackets [ ] apply in the short transverse direction for short transverse dimensions of 3.0″ or greater. Size X” – Y” reads “over X” to Y”, inclusive.”
Tensile Requirements – Alpha-Beta Alloys:
| Alloy | Condition | Thickness, Diameter or Distance Between Flats | Tensile Strength (KSI) | Yield Strength at 0.2% (KSI) | % Elongation in 4D | % Reduction of Area |
|---|---|---|---|---|---|---|
| Ti-6Al-4V | A | 4.00″ & under | 130 | 120 | 10 | 25 |
| Ti-6Al-4V | A | 4.00″ – 6.00″ | 130 | 120 | 10 [8] | 20 [15] |
| Ti-6Al-4V | STA (rounds, squares, hex) | 0.500″ & under | 165 | 155 | 10 | 20 |
| Ti-6Al-4V | STA (rounds, squares, hex) | 0.500″ – 1.00″ | 160 | 150 | 10 | 20 |
| Ti-6Al-4V | STA (rounds, squares, hex) | 1.00″ – 1.50″ | 155 | 145 | 10 | 20 |
| Ti-6Al-4V | STA (rounds, squares, hex) | 1.50″ – 2.00″ | 150 | 140 | 10 | 20 |
| Ti-6Al-4V | STA (rounds, squares, hex) | 2.00″ – 3.00″ | 140 | 130 | 10 | 20 |
| Ti-6Al-4V ELI | A | 1.50″ & under | 130 | 120 | 10 | 25 |
| Ti-6Al-4V ELI | A | 1.50″ – 3.00″ | 125 | 115 | 10 | 20 |
| Ti-3Al-2.5V | A | 1.00″ & under | 90 | 75 | 15 | 30 |
| Ti-6Al-6V-2Sn | A | 1.50″ & under | 148 | 137 | 10 | 20 |
| Ti-6Al-6V-2Sn | A | 1.50″ – 3.00″ | 143 | 131 | 10 | 20 |
| Ti-6Al-6V-2Sn | A | 3.00″ – 4.00″ | 137 | 129 | 10 [8] | 20 [15] |
| Ti-6Al-6V-2Sn | STA | 1.00″ & under | 175 | 160 | 8 | 20 |
| Ti-6Al-6V-2Sn | STA | 1.00″ – 2.00″ | 170 | 155 | 8 | 20 |
| Ti-6Al-6V-2Sn | STA | 2.00″ – 3.00″ | 155 | 145 | 8 | 20 |
| Ti-6Al-6V-2Sn | STA | 3.00″ – 4.00″ | 150 | 140 | 8 [6] | 20 [15] |
| Ti-6Al-2Sn-4Zr-2Mo | DA | 3.00″ & under | 130 | 120 | 10 | 25 |
| Ti-6Al-2Sn-4Zr-6Mo | DA | 2.00″ & under | 160 | 150 | 10 | 25 |
| Ti-6Al-2Sn-4Zr-6Mo | DA | 2.00″ – 4.00″ | 150 | 140 | 8 [6] | 20 [15] |
| Ti-6Al-2Sn-4Zr-6Mo | STA | 2.50″ & under | 170 | 160 | 10 | 20 |
| Ti-6Al-2Sn-4Zr-6Mo | STA | 2.50″ – 3.00″ | 165 | 155 | 8 [6] | 15 [12] |
| Ti-6Al-2Sn-4Zr-6Mo | STA | 3.00″ – 4.00″ | 160 | 150 | 8 [6] | 15 [12] |
| Ti-7Al-4Mo | A | 1.00″ & under | 145 | 135 | 10 | 20 |
| Ti-7Al-4Mo | A | 1.00″ – 2.00″ | 140 | 130 | 10 | 20 |
| Ti-7Al-4Mo | A | 3.00″ – 6.00″ | 140 | 130 | 10 [8] | 20 [15] |
| Ti-7Al-4Mo | STA | 1.00″ & under | 170 | 160 | 8 | 15 |
| Ti-7Al-4Mo | STA | 1.00″ – 2.00″ | 160 | 150 | 8 | 15 |
| Ti-7Al-4Mo | STA | 2.00″ – 4.00″ | 150 | 140 | 8 [6] | 15 [12] |
Minimum values in any grain direction. Values in brackets [ ] apply in the short transverse direction for short transverse dimensions of 3.0″ or greater. For annealed Ti-6Al-6V-2Sn, maximum yield strength may not exceed the minimum by more than 25 ksi. Requirements for Ti-6Al-4V STA rectangles vary with thickness and width and are available on request. Section size and cross-section limits apply to each alloy. Size X” – Y” reads “over X” to Y”, inclusive.”
Tensile Requirements – Beta Alloys:
| Alloy | Condition | Thickness, Diameter or Distance Between Flats | Tensile Strength (KSI) | Yield Strength at 0.2% (KSI) | % Elongation in 4D | % Reduction of Area |
|---|---|---|---|---|---|---|
| Ti-8Mo-8V-2Fe-3Al | ST | 2.00″ & under | 130 | 120 | 10 | 24 |
| Ti-8Mo-8V-2Fe-3Al | ST | 2.00″ – 4.00″ | 125 | 120 | 8 [6] | 16 [12] |
| Ti-8Mo-8V-2Fe-3Al | STA | 2.00″ & under | 180 | 170 | 8 | 16 |
| Ti-8Mo-8V-2Fe-3Al | STA | 2.00″ – 4.00″ | 180 | 170 | 6 [4] | 12 [10] |
| Ti-11.5Mo-6Zr-4.5Sn | ST | 1.625″ & under | 110 | 90 | 15 | 50 |
| Ti-11.5Mo-6Zr-4.5Sn | ST | 1.625″ – 3.00″ | 100 | 90 | 15 | 50 |
| Ti-11.5Mo-6Zr-4.5Sn | ST | 3.00″ – 4.00″ | 100 | 90 | 10 | 35 |
| Ti-11.5Mo-6Zr-4.5Sn | STA (1075°F) | 3.00″ & under | 135 | 130 | 12 | 40 |
| Ti-11.5Mo-6Zr-4.5Sn | STA (925°F) | 1.625″ & under | 180 | 175 | 8 | 22 |
| Ti-11.5Mo-6Zr-4.5Sn | STA (925°F) | 1.625″ – 3.00″ | 180 | 175 | 6 | 10 |
| Ti-3Al-8V-6Cr-4Mo-4Zr | ST | 1.50″ & under | 125 | 120 | 10 | 30 |
| Ti-3Al-8V-6Cr-4Mo-4Zr | ST | 1.50″ – 4.00″ | 120 | 115 | 10 [8] | 25 [20] |
| Ti-3Al-8V-6Cr-4Mo-4Zr | STA | 1.50″ & under | 190 | 180 | 8 | 15 |
| Ti-3Al-8V-6Cr-4Mo-4Zr | STA | 1.50″ – 3.00″ | 180 | 170 | 8 [6] | 15 [5] |
| Ti-3Al-8V-6Cr-4Mo-4Zr | STA | 3.00″ – 4.00″ | 170 | 160 | 8 [3] | 15 [5] |
| Ti-13V-11Cr-3Al | ST | 7.00″ & under | 125 | 120 | 10 | 25 |
| Ti-13V-11Cr-3Al | STA | 4.00″ & under | 170 | 160 | 6 [2] | 10 [5] |
Minimum values for products with a cross-sectional area of 16 sq. in. or less, in any grain direction. Aging temperatures are shown where the specification lists more than one STA condition. Values in brackets [ ] apply in the short transverse direction for short transverse dimensions of 3.0″ or greater. Size X” – Y” reads “over X” to Y”, inclusive.”
Also Known As:
MIL-T-9047, MIL-T-9047G, MIL-T-9047 AB-1, MIL-T-9047 Ti-6Al-4V, MIL-T-9047 6Al-4V ELI, MIL-T-9047 CP-70, MIL-T-9047 5Al-2.5Sn, MIL-T-9047 6Al-6V-2Sn, MIL-T-9047 6Al-2Sn-4Zr-6Mo, Mil Spec Titanium Bar, Military Specification Titanium Round Bar, Titanium Reforging Stock, Ti 6-4 Bar, UNS R56400
Available Forms:
Frequently Asked Questions:
What alloys does MIL-T-9047 cover?
MIL-T-9047 covers 16 compositions: CP-70, Ti-5Al-2.5Sn, Ti-5Al-2.5Sn ELI, Ti-6Al-2Cb-1Ta-0.8Mo, Ti-8Al-1Mo-1V, Ti-3Al-2.5V, Ti-6Al-4V, Ti-6Al-4V ELI, Ti-6Al-6V-2Sn, Ti-6Al-2Sn-4Zr-2Mo, Ti-6Al-2Sn-4Zr-6Mo, Ti-7Al-4Mo, Ti-8Mo-8V-2Fe-3Al, Ti-11.5Mo-6Zr-4.5Sn, Ti-3Al-8V-6Cr-4Mo-4Zr, Ti-13V-11Cr-3Al.
What is the difference between MIL-T-9047 and MIL-T-9046?
MIL-T-9047 covers rolled or forged bar and reforging stock, while MIL-T-9046 covers sheet, strip and plate. MIL-T-9047 identifies each alloy by its composition, while MIL-T-9046 uses codes such as CP-1 and AB-1.
What does MIL-T-9047 AB-1 mean?
MIL-T-9047 itself lists alloys by composition, but buyers often borrow the MIL-T-9046 code AB-1, which stands for Ti-6Al-4V. A callout of MIL-T-9047 AB-1 therefore normally means Ti-6Al-4V bar to MIL-T-9047. Confirm the alloy and condition on your drawing or purchase order.
Is MIL-T-9047 the same as AMS-T-9047?
AMS-T-9047 is the SAE aerospace specification for the same titanium bar and reforging stock, and the two are often cross-referenced, but they differ in details. Always order to the specification called out on your drawing or purchase order.
What conditions is MIL-T-9047 bar supplied in?
Bars are supplied annealed (A), duplex annealed (DA), solution treated (ST) or solution treated and aged (STA), depending on the alloy and the condition ordered. Annealed alpha-beta bar can also be ordered with a requirement to meet the STA properties after heat treatment.
Do you provide certifications with MIL-T-9047?
Yes. All MIL-T-9047 material ships with Certified Material Test Reports (CMTR) and a Certificate of Conformance, with full traceability to the producing mill.
What is MIL-T-9047 used for?
Typical applications include aerospace fasteners and fittings, landing gear and airframe structural parts, engine components, and missile and ordnance hardware.
Related Specifications:
MIL-T-9046 (titanium sheet, strip & plate) | AMS 4928 (Ti-6Al-4V annealed bar) | AMS 4965 (Ti-6Al-4V STA bar) | AMS 6931 (Ti-6Al-4V annealed bar) | AMS 4971 (Ti-6Al-6V-2Sn heat treatable bar & forgings) | ASTM B348 (titanium bar & billet)
View all titanium grades and specifications →
Disclaimer:
This Data is for voluntary use only and as such is not to be relied upon in place of the full specification. Information could contain errors that company will not be held responsible. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon. Please note the information stated above has no guarantee of accuracy or whether the datasheet is up to date. The information provided in this datasheet has been drawn from various recognized sources, including AMS and ASTM Standards, recognized industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

